Quick answer: A Vaillant F63 usually means the boiler’s circuit board has a memory fault, known as an EEPROM fault. It’s most often a failing board, or one that wasn’t set up properly after it was fitted. Try one reset by the manual. If the code comes back, the fix is usually a new circuit board, and that is where the repair-or-replace question gets serious.
Sorry to be the bearer of mixed news here, because I know no heating is miserable. The good thing is that it points to one clear area, so you’ll have a decision to make rather than a long guessing game.
What does F63 mean on a Vaillant boiler?
The circuit board, or PCB, is the boiler’s brain. It holds a small memory chip called an EEPROM that stores your boiler’s settings and operating data. F63 means the board has trouble reading or keeping that information.
Secondary sources say F63 applies across Vaillant models, but I’d still check your manual’s code table, because wording can differ between ranges. Compared with a sensor code, which points at one cheap part, F63 points at the board itself.
What causes a Vaillant F63 fault?
There are fewer causes here than with most codes, and the fixes are not cheap, which is why it’s worth understanding them.
| Cause | Tell-tale sign | Usual fix | Rough cost guide* |
|---|---|---|---|
| Faulty circuit board | F63 returns after a reset, and the boiler won’t run | Engineer replaces the board | About £350 to £450, up to about £790 in some cases |
| Board set up incorrectly after installation or service | Fault appears soon after work on the boiler | Engineer re-checks the board’s setup | Ask for a fixed quote |
| Loose connection to the board | Code is intermittent | Engineer re-seats and tests the connection | Ask for a fixed quote |
| Age of the board | Boiler is well past 8 years, with other odd faults | Board or boiler replacement | As above, or compare a new boiler |
*Guide figures are based on typical UK repair prices published online, and they’re only a rough steer. Prices vary with the model, parts availability and the job itself, so please treat them as ballpark figures and ask for a fixed quote.
How do you fix a Vaillant F63? Can I reset it?
You can try one reset. Sometimes a board will recover, though if the memory is genuinely failing it won’t hold for long.
- Write down the code and any other lights or messages on the display.
- Follow the reset instructions in your boiler’s manual.
- If the boiler starts and runs normally, book an engineer anyway, as the fault may return.
- If F63 comes back, stop. Further resets won’t fix it.
Please don’t open the boiler or try to check the board. Everything involved is electronic and specialist, and it’s far too easy to damage it further.
If you’re not sure what your manual allows, check it first. A Gas Safe registered engineer can then confirm what the board needs.
Is a Vaillant F63 fault dangerous?
It isn’t a gas or carbon monoxide fault, and the boiler stopping is the safe response. The real risk is the cost and the time without heat, particularly in an Edinburgh winter, so it’s worth getting a quote quickly instead of waiting to see if it clears.
Should I repair or replace my Vaillant boiler?
This is the code where I’d have the conversation early. A new circuit board is usually about £350 to £450, and it can reach about £790 in some cases. That is a large share of the price of a new boiler. If your Vaillant is over 8 years old and out of warranty, get a price for replacement before you agree to a big repair. A new board in an ageing boiler doesn’t stop the next part failing, whereas a new boiler from our Edinburgh team comes with a fresh warranty and better efficiency.
If the boiler is only a few years old, or still under warranty, repair is the sensible route, and your warranty may cover the part. Ask your engineer to explain the numbers either way.
How can I stop F63 coming back?
You can’t guarantee it, since memory faults often come down to age. A yearly boiler service does help by spotting loose connections, and it gives an engineer the chance to tell you honestly how the board and the rest of the boiler are holding up.
Vaillant boiler repairs across Edinburgh and Scotland
The Edinburgh Boiler Company repairs, services and replaces boilers across Edinburgh and Scotland. Every engineer is Gas Safe registered and we’re a Which? Trusted Trader. We cover EH1 to EH55, including Dalkeith, Penicuik, Musselburgh, Bathgate and Peebles. Whatever you decide, you can book a Vaillant repair to get a fixed quote, or read more in our Vaillant error codes guide.
Frequently asked questions about the Vaillant F63 fault
What’s the difference between F63 and F64?
F63 is a memory fault on the circuit board, while F64 is a different electronics problem, and you can read about it in our Vaillant F64 guide. Both may end in a board visit, but an engineer needs to confirm which.
Is F63 related to F61 or F62?
Not directly. F61 and F62 are gas valve codes, whereas F63 is a memory fault on the circuit board. Have a look at Vaillant F61 and Vaillant F62 to compare.
Can a reset clear F63 for good?
Occasionally for a while, but if the memory is faulty the code usually returns. One reset is fine, after which it needs an engineer.
Is it worth fixing a Vaillant with F63?
It depends on age and warranty. On a young boiler it often is. On one over 8 years old and out of warranty, compare the board cost with a replacement first.
Related codes: Vaillant F62 and Vaillant F64.